国外耳机发烧友的DIY耳放

atp · 发表于 2005-1-24 22:13:28

交易区新帖推荐

感谢关注耳机俱乐部网站，注册后有更多权限。

您需要登录才可以下载或查看，没有账号？注册

x

crossfeed

diy cable

rpwt · 发表于 2005-1-24 22:16:57

sf?``

atp · 发表于 2005-1-24 22:21:20

atp · 发表于 2005-1-24 22:23:50

atp · 发表于 2005-1-24 22:24:25

atp · 发表于 2005-1-24 22:25:33

当然帖的都是精品啦。

atp · 发表于 2005-1-24 22:26:14

点击有大图。

leolss · 发表于 2005-1-24 23:37:25

有些做的还真挺漂亮的，花里胡梢的。看第一眼就有想拥有的冲动。

atp · 发表于 2005-1-24 23:58:49

倒数第二个挺逗的。

念苍僧 · 发表于 2005-1-25 00:17:18

我终于知道谁借鉴谁了 [s:38]

atp · 发表于 2005-1-25 00:51:51

楼上的咋了？

岚风 · 发表于 2005-1-25 01:36:48

果然强淫啊！

atp · 发表于 2005-1-25 01:50:49

下面是引用念苍僧于2005-01-25 00:17发表的:

我终于知道谁借鉴谁了 [s:38]

这个耳放的原型是在中国买的，其他的是改装的

部分原文：

dblab hp-100a recase/mod

Well well, finally. Got the kit while I was in China over summer, just finished it. The original group buy thread is here, if you're interested.

The chassis style is an extension of the dblab ppa project, it's just longer and only one output jack is present. Four heatsinks line each side of the amp board, with MOSFETs and regulators connected with teflon coated silver wire.

Basically, almost everything on the board has been swapped out. Resistors, capacitors, etc. etc... The filtered IEC power jack has been replaced by a regular jack, and the RCA jacks replaced with a higher quality pair. A second input (aux) and pre out were eliminated as I have no use for them.

Also, the stock Hitachi J77/K214 MOSFET pairs have been replaced with higher speced (and more expensive) Toshiba J313/K2013 pairs. The pinout was different, but since I was wiring them off board anyway, this wasn't such a big problem. Also, the 8050 transistors have been "replaced" with 8050s (the kit came with some other set of transistors).
。。。。。。。。。。。。。

http://www6.head-fi.org/forums/s ... 1073277#post1073277

xpxply · 发表于 2005-1-25 05:38:03

这个做的真漂亮外壳是用什么盒子做的?打火机?那么大?....

atp · 发表于 2005-1-25 08:01:13

That's a Cigarette case

香烟盒。

		自动登录	找回密码
密码			注册

[耳机] 国外耳机发烧友的DIY耳放

感谢关注耳机俱乐部网站，注册后有更多权限。